• Bravo BTP12 Volt Digial Electric Air Pump

    $179.95

    FEATURES
     - Power supply 12V DC
     - Maximum absorption 20 A
     - Maximum pressure 1 bar / 14.5 psi
     - Maximum flow rate Turbine 450 l/min Piston 160 l/min
     - Weight 1.7 Kg

     - Dimensions 290x100x150 mm
    Item Name: BTP 12 Digital Electrical Inflator
    Shipping weight: 6 lbs
    Price: 179.00

    The Bravo BTP 12 High-Pressure Pump is the perfect solution for quickly inflating your raft, cataraft, IK or SUP board. Hook it up to a 12 volt battery and it puts out up to 15 psi air pressure.

    • Inflate and deflate quickly with this powerful 12 volt pump.
    • It's easy to know exactly what pressure you have with the built-in 0-15 psi gauge.
    • 9 foot long battery cables and 6 foot air hose gives you good reach.
    • Eight valve adapters, including one specifically for the Leafield C7, links up to most common valves.
    • Pump, cables and hose fit in a handy zipper carry case, with shoulder strap.
    Never operate Bravo with vehicle motor running - it can damage the pump due to a higher voltage output.

    Long periods of use can cause overheating and damage the product.
    Do not use for more than 20 minutes continuously.

    INFLATION OPERATION
    1 From the supplied fittings, select the reducer that engages and opens the valve of the inflatable structure.
    2 Insert the selected adaptor on the braided joint on the end of the tube.
    3 Tighten the adaptor on to the inflation side of the inflator (OUT).
    4 Connect the terminals paying attention to the polarity and press the (power) button: the digital panel will come on.
    5 The power supply must be within the range of 8.5-13.5 V, otherwise the inflator turns off automatically. In this case, the left or right LED flashes depending if the power supply is too low or too high.
    6 If you want to change the unit of measurement, press the (MODE Kpa, mbar, psi, bar) button with the tip of a biro.
    7 Enter the maximum desired pressure using the two (SET PRESSURE -/+) buttons.
    8 Press the (START) button. The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically.
    9 During inflation, the digital panel shows the pressure that the inflator has reached. As soon as the entered pressure has been reached, the inflator turns off automatically.
    The inflator can be turned off at any time by pressing (OFF).


    ATTENTION: Protect the inflator from sand by keeping it in the bag provided: if sand gets into the inflator, it could get JAMMED.
    DEFLATING OPERATION
    1/2/5 As above.
    3 Tighten the adaptor onto the deflation side of the inflator (IN).
    4 Connect the terminals and press the (power) button: the digital panel will come on.
    6 Press the (START) button.
    7 THE INFLATOR DOES NOT TURN OFF AUTOMATICALLY !!!!!!
    When the inflatable is completely deflated, switch OFF the inflator immediately to avoid overheating the motor.

    SAND FILTER MAINTENANCE
    The inflator has a filter compartment under the inflation chuck (IN).
    - We recommend to keep them clean for the inflator to be longer lasting and more effective.
    - Loosen the two screws blocking the inflation chuck (IN).
    - Lift the chuck and take it off.
    - Clean with compressed air or replace if it is too dirty.


    WARRANTY
    The inflator is guaranteed for 2 years.
    In case of claims do not touch the device and send it free-destination to Scoprega S.p.a. – Ningbo Bravo or directly to the seller

    Long periods of use can cause overheating and damage the product.
    Do not use for more than 20 minutes continuously.

    INFLATION OPERATION
    1 From the supplied fittings, select the reducer that engages and opens the valve of the inflatable structure.
    2 Insert the selected adaptor on the braided joint on the end of the tube.
    3 Tighten the adaptor on to the inflation side of the inflator (OUT).
    4 Connect the terminals paying attention to the polarity and press the (power) button: the digital panel will come on.
    5 The power supply must be within the range of 8.5-13.5 V, otherwise the inflator turns off automatically. In this case, the left or right LED flashes depending if the power supply is too low or too high.
    6 If you want to change the unit of measurement, press the (MODE Kpa, mbar, psi, bar) button with the tip of a biro.
    7 Enter the maximum desired pressure using the two (SET PRESSURE -/+) buttons.
    8 Press the (START) button. The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically.
    9 During inflation, the digital panel shows the pressure that the inflator has reached. As soon as the entered pressure has been reached, the inflator turns off automatically.
    The inflator can be turned off at any time by pressing (OFF).
    ATTENTION: Protect the inflator from sand by keeping it in the bag provided: if sand gets into the inflator, it could get JAMMED.
    DEFLATING OPERATION
    1/2/5 As above.
    3 Tighten the adaptor onto the deflation side of the inflator (IN)
    .
    4 Connect the terminals and press the (power) button: the digital panel will come on.
    6 Press the (START) button.
    7 THE INFLATOR DOES NOT TURN OFF AUTOMATICALLY !!!!!!
    When the inflatable is completely deflated, switch OFF the inflator immediately to avoid overheating the motor.
    SAND FILTER MAINTENANCE

    The inflator has a filter compartment under the inflation chuck (IN).
    - We recommend to keep them clean for the inflator to be longer lasting and more effective.
    - Loosen the two screws blocking the inflation chuck (IN).
    - Lift the chuck and take it off.
    - Clean with compressed air or replace if it is too dirty.